Differences

This shows you the differences between two versions of the page.

--- networking:cisco:intervlan-mls [2026/02/03 22:07] – [Konfigurasi SVI pada VLAN] ilyasa
+++ networking:cisco:intervlan-mls [2026/02/03 22:22] (current) – [Testing] ilyasa
@@ Line 1: / Line 1: @@
 {{indexmenu_n>035}}
-====== Cisco : inter-vlan Multi Layer Switch ======
+====== Cisco : inter-vlan Multi Layer Switch SVI (Switch virtual interface ) ======
 Pada halaman sebelumnya [[roas|]] kita telah menkonfigurasi intervlan dengan metode ROAS. Sekarang kita akan menkonfigurasi inter vlan menggunakan Multilayer Switch (MLS). MLS merupakan Switch yang mempunyai kemampuan routing layer 3. Sehingga kita tidak memperlukan lagi router sebagai penghubung jaringan antar VLAN.
@@ Line 21: / Line 21: @@
 </code>
 ===== Topologi =====
-Gambar topology
+{{ :networking:cisco:cisco_mls.png?nolink |}}
-Goals Topology
+Topologi sama dengan halaman sebelumnya [[roas|]], Akan tetapi kita menghapus Router dan menggantinya dengan SW1  dengan Multilayer Switch. Untuk konfigurasi SW2 bisa ke halaman sebelumnya.
+Goalnya masih sama yaitu menhubungkan kedua segment jaringan.
 ===== Konfigurasi =====
-  * **Step 1 : Pembuatan VLANs**
+  * **Step 1 : Konfigurasi VLAN Pada MLS**
 <code>
-Switch(config)#vlan 10
+MLS1(config)#vlan 10
-Switch(config-vlan)#name BIRU
+MLS1(config-vlan)#name BLUE
-Switch(config-vlan)#exit
+MLS1(config-vlan)#vlan 20
+MLS1(config-vlan)#name MAGENTA
-Switch(config)#vlan 20
-Switch(config-vlan)#name MAGENTA
-Switch(config-vlan)#exit
 </code>
-  * **Step 2 : Assign VLANs ke Ports**
+  * **Step 2 : Konfigurasi Access Ports MLS**
 <code>
-Switch(config)#interface f0/1
+MLS1(config)#interface range f0/1-2
-Switch(config-if)#switchport mode access
+MLS1(config-if-range)#switchport mode access
-Switch(config-if)#switchport access vlan 10
+MLS1(config-if-range)#switchport access vlan 10
-Switch(config-if)#exit
+MLS1(config)#interface range f0/3-4
+MLS1(config-if-range)#switchport mode access
-Switch(config)#interface f0/2
+MLS1(config-if-range)#switchport access vlan 20
-Switch(config-if)#switchport mode access
+</code>
-Switch(config-if)#switchport access vlan 10
+  * **Step 3 : Konfigurasi trunk interface**
-Switch(config-if)#exit
+<code>
+MLS1(config)#interface g0/1
+MLS1(config-if)#switchport mode trunk
+Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode.
+MLS1(config-if)#switchport trunk encapsulation dot1q
+MLS1(config-if)#switchport mode trunk
+MLS1(config-if)#switchport trunk allowed vlan 10,20
+</code>
+  * **Step 4 : Konfigurasi Switch virtual interface **
+<code>
+MLS1(config)#interface vlan 10
+MLS1(config-if)#ip address 192.168.1.254 255.255.255.0
+MLS1(config)#interface vlan 20
+MLS1(config-if)#ip address 192.168.2.254 255.255.255.0
+</code>
+  * **Step 5 : Pastikan pada MLS ip routing posisi on **
+<code>
+MLS1(config)#ip routing
 </code>
 ===== Testing =====
+* **PC1 -> PC3/PC7**
+<code>
+C:\>ping 192.168.2.3
+Pinging 192.168.2.3 with 32 bytes of data:
+Reply from 192.168.2.3: bytes=32 time<1ms TTL=127
+Reply from 192.168.2.3: bytes=32 time<1ms TTL=127
+Reply from 192.168.2.3: bytes=32 time<1ms TTL=127
+Reply from 192.168.2.3: bytes=32 time<1ms TTL=127
+Ping statistics for 192.168.2.3:
+    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
+Approximate round trip times in milli-seconds:
+    Minimum = 0ms, Maximum = 0ms, Average = 0ms
+C:\>ping 192.168.2.7
+Pinging 192.168.2.7 with 32 bytes of data:
+Reply from 192.168.2.7: bytes=32 time=6ms TTL=127
+Reply from 192.168.2.7: bytes=32 time<1ms TTL=127
+Reply from 192.168.2.7: bytes=32 time<1ms TTL=127
+Reply from 192.168.2.7: bytes=32 time<1ms TTL=127
+Ping statistics for 192.168.2.7:
+    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
+Approximate round trip times in milli-seconds:
+    Minimum = 0ms, Maximum = 6ms, Average = 1ms
+</code>